How did our sea trial go?

Sea Trial, Survey, Mechanical Inspection & Haul Out

Last Weds, February 20th, Scott and I had the sea trial, survey and mechanical inspection scheduled for the Bayliner 4087 we made an offer on. Seattle has been experiencing record breaking snow levels and conditions this month and once again it threatened to snow on Wednesday! Based on the weather forecast, I was nervous. You know me, when it comes to weather, I’m a nut. The last thing I wanted to do was haul out in the snow! Here’s a picture that our boat yard shared the week before!

We hired Chuck Solarek, of CSW Surveyors and I highly recommend him! Chuck came in with loaded guns. Not only is he SAMS accredited (Society of Marine Surveyors Society), but he has twenty-four years experience as a naval submarine engineer. He had so much equipment with him, that I thought he had other members on his team. In the end, his survey and mechanical inspection was so detailed and thorough, we couldn’t have asked for more.

Let sea trials begin

Scott and I asked my brother-in-law Kurt to join us for the sea trial. He is a retired Washington State Ferry engineer and a life long boater himself. You will recall, he helped us out many times with Kokomo – especially during our trip to the San Juans Islands.

Also along on the trip, was our broker Steve Thoreson, from Union Marine and the captain, who was hired by Elliott Bay Yacht Sales. (certainly different than when Ed the owner of Kokomo took us out!

We all met at the marina around 9:15am and by then Chuck had been on the boat for a bit doing his inspection.

We left Elliott Bay Marina around 9:30am and headed towards Shilshole Marina and Seaview Boat Yard. Low and behold, the weather was perfect! We had calm seas and a slight mist, but that was it!

On our trip to Seaview, we motored at about 11 knots, which was a very pleasant pace. Unlike Kokomo, we could talk and hear each other. However, at this pace, it would take us eight hours to get to the San Juan Islands, versus three on Kokomo. Scott took the helm at the bridge on the way up and I sat down below in the salon. During that time, Along the way, Kurt and Chuck were checking different systems.

Arriving at Seaview Boatyard

If you remember from the last time we hauled out, I was scared to death to climb out of the boat while it was in the slings. Well, this time it was just as bad, if not worse! I still can’t believe this is how they do this!! So unsafe. Each passenger, walks out to the bow, steps over the railing (that’s great if you are tall), reaches for the WET ladder that is about a foot or two away and starts to climb out. Don’t mind that you are 15′ in the air!

I was so worried my foot was going to slip or my hand would lose a grip. My heart was racing when I landed on the pier. I then told everyone, they were picking me up on the dock when we were done! LOL

Hauling out the boat

We had one hour to have Chuck inspect the hull, drives, propellers and trim tabs. Since I won a free power wash at the Seattle Boat Show, I had them power wash the bottom, so we could get a clearer picture of what it looked like.

Remember what Kokomo looked like when we hauled out? Not only did it need to be painted, but all of the zincs were shot! (see below)

Well, shockingly this boat was in perfect shape! (still seems odd to me, since they say the last time they hauled out was in 2014!) So strange, but that’s great news!

Poor Chuck was soaked from inspecting the hull while they pressure washed it!

Time to head back for home & sea trials

An hour and $425 later, it was time to put the boat back in the water.

We left Seaview boatyard around 11:15am and headed out to Elliott Bay. Once out in the bay, Chuck had Scott run the engines, while he checked them. Remember, these are twin Cummins diesel engines. From our cruising speed of 11 knots/1000 RPMs, Chuck had us increase the RPMs to 1500, then to 2000 and then to wide open at 2500 RPMs. You would never run a semi-displacement boat at that speed, as it’s not only not good for the engines, but you would get terrible fuel consumption. For the best fuel consumption, between 1000-1200 RPMs is ideal.

What we did learn about diesel engines is three primary things:

• Never ever run out of gas (remember our story from September?)
• When cruising with diesel engines, it is important to run at 80% of your max RPM during your last 20 minutes of cruising. That’s important to remember if you plan on only cruising the bay.
• When docking, leave the engines running at idle for about 5 minutes to allow them to cool off. Unlike gas engines, diesel engines cool off while running versus after they shut down.

Once back at the dock, the last thing to check was the infamous tender – did it run? Steve dropped it (sort of) into the water, then Scott climbed into it haphazardly and was able to start it. The running lights work, but maybe not the CD Player. LOL

Survey results?

Well it wouldn’t be a boating journey story if there wasn’t a snag right? Remember when we trying to close on Kokomo and the owner kept going out of town, so it took a month? Let’s hope that’s not the case this time.

Long story short, the survey and inspection came back pretty good. We do have to some work, nothing too major and Lake Union Sea Ray Service Department can do all of the work. Scott and I have accepted the survey and now we wait to go to escrow next week – we hope! Our lender requires our boat be documented with the Coast Guard. We are waiting for the documentation reports to make sure it’s not a stolen boat before we can go to escrow. Guess what? The Coast Guard is a bit back logged due to the government shutdown.

Then we are scheduled to close on Weds, March 6th – but Scott will be in Miami, FL. This title company doesn’t like to use “power of attorney” signatures, so he either needs to find a notary in Miami or be present. So our hope is that we move it to Thursday, March 7th if the Coast Guard docs come back in time – the night we fly out to the Caribbean on our tall ship cruise. If that doesn’t happen, it will have to be postponed until we return, mid-March.

Then what?

Once we take possession, our broker Steve will spend time with both us teaching us how to dock it and back it out of the slip. Everyone says it will be much much easier than our old boat, so let’s hope so. Since we will be taking it to Lake Union Sea Ray for service, we’ll go thru the Ballard Locks with Steve that same day and get some time under our belts (he can dock it at the shop though) 😉

So stay tuned! Our next update will most likely be our trip to the Caribbean and not about the boat! We have some work to do on it, both mechanically and aesthetically and we’ll share all of that with you too, once we are official.

As always, thank you for following our blog! Be sure to follow us on Facebook, Instagram, Twitter and YouTube @BoatingJourney #boatingjourney

Watch our full sea trial and survey on Episode 29 on our YouTube channel here:

Cheers, Scott and Ally